Calgary Jeep Association

4x4 Related Groups => Tech Talk => Topic started by: RUBI on August 12, 2008, 11:55:16 PM

Title: Edge Products......Input????
Post by: RUBI on August 12, 2008, 11:55:16 PM: Anybody have personel experience with this ............... http://www.edgeproducts.com/product.php?pk=84&pvk=261

Found this write up......... http://jeepforum.com/forum/showthread.php?t=403511
Title: Re: Edge Products......Input????
Post by: dac on August 13, 2008, 07:49:00 AM: I've got the kit with the air intake on an 02 TJ Sport. Also have cat back exhaust and header. With 31's and the 3.73 ratio mine had a lot more snap than the stock rubi for comparison. I noticed more low end torque, could do 40-50kph in 5th and accelerate out of it. Now than I have 33's I lost a bit but it's still pretty strong. With the 31's when I put it on I didn't notice a difference in mileage; with the 33's I've lost a little bit, not much. Installing it was really easy.
Title: Re: Edge Products......Input????
Post by: RUBI on August 14, 2008, 02:59:36 AM: Who did you get ur Kit through and what was the cost ????????????
???
Title: Re: Edge Products......Input????
Post by: Matt4x4 on August 14, 2008, 10:37:04 PM: That product was on Truck Universe today, sounds like a good product
They said 25 hp and 25 ft lb increase
Title: Re: Edge Products......Input????
Post by: RUBI on August 15, 2008, 01:13:16 AM: Ordered one today direct from Edge........I'd tend to be pretty sceptical about 25HP and ft/lbs of torque, but any increase over stock is good !!!! ::)
Title: Re: Edge Products......Input????
Post by: calltrex on August 15, 2008, 08:19:20 AM: Quote from: RUBI on August 15, 2008, 01:13:16 AM
Ordered one today direct from Edge........I'd tend to be pretty sceptical about 25HP and ft/lbs of torque, but any increase over stock is good !!!! ::)

make sure you get the canadian version. theres a different connector or something like that...
Title: Re: Edge Products......Input????
Post by: Matt4x4 on August 15, 2008, 03:48:21 PM: you are right, any increase over stock is good

Been looking into power adders myself, but I think I will leave my heep stock with a few add-ons for mild wheeling. This is my daily driver.

I will have my other truck to beat to hell and break stuff. Thinking a lifted 1990's stroker 454/205 doubler chev crewcab with 44's on d60's, shortened wheelbase. My dodge truck is the company truck and backup 8)
Title: Re: Edge Products......Input????
Post by: dac on August 21, 2008, 05:38:46 PM: I bought mine through Mopac, seemed to be the best deal in town at the time.
Title: Re: Edge Products......Input????
Post by: calltrex on August 21, 2008, 06:02:34 PM: how much?
Title: Re: Edge Products......Input????
Post by: RUBI on August 21, 2008, 07:10:04 PM: Direct from Edge...... I'll let you know the total when it arrives.
I didn't forget bout ya Dava, still trying to round up the missing piece ;)

http://www.edgeproducts.com/products.php?car_motor_key=50&category_key=all
Title: Re: Edge Products......Input????
Post by: dac on August 21, 2008, 07:54:45 PM: Mopac was 936 plus tax for the full kit in Sept. 2006. Probably lower by now though.
Title: Re: Edge Products......Input????
Post by: RUBI on August 22, 2008, 12:41:19 AM: $545.59 for the TB and module kit includes shipping handling etc....... ( no air intake tube/filter)
Title: Re: Edge Products......Input????
Post by: RUBI on September 04, 2008, 01:17:22 PM: FINALLY !!!!!!! >:(
Just finished the install on the EDGE TB and module...........WOW !!! :o Didn't think it would be as impressive as it is, right from idle, mid range and up it pulls noticeably harder through all the gears. Can't wait to get out and play with it wheeling.........still need those short arms before I can get out again.
Seems there is always something holding me up !!! :-[