Calgary Jeep Association

Author Topic: shock lower bushing  (Read 1729 times)

0 Members and 4 Guests are viewing this topic.

Offline Zombie

  • UberWheeler
  • Posts: 398
  • Jeff the Zombie Jeep
shock lower bushing
« on: December 04, 2009, 01:39:26 AM »
I had the jeep in for an alignment today and the lower shock bushings are worn out and need to be replaced.
I believe the shocks are Rancho's.

anyone know if I can replace the bushings and not have to replace the shocks?

if so, where would I get the bushings??

thanks
steve
97 Red XJ, 4.5", 31" mud's, ARB front, 9500lb winch, bushwhacker's, warn sliders, HnT SYE and CV drive shaft - written off and sold for parts :(

Offline tubby

  • Talks waaay too much!
  • Posts: 1349
  • Life's too short for a fulltime job
Re: shock lower bushing
« Reply #1 on: December 04, 2009, 02:27:27 AM »
You can go to Modern Motors or National4x4 and pick them up. They carry Rancho and should have  bushings available for you. You don't have to replace the whole shock. Use a bench vise and some sockets to push the old ones out and press the new ones in. Use some lube(vaseline) to help get them in. Standens also has shock bushings as well.
« Last Edit: December 04, 2009, 02:39:35 AM by tubby89 »
Lockers
Cuz ya can't kick arse with only one leg

Offline Zombie

  • UberWheeler
  • Posts: 398
  • Jeff the Zombie Jeep
Re: shock lower bushing
« Reply #2 on: December 04, 2009, 09:03:52 AM »
sweet.
have to look at replacing the rear springs, so I might check standins for that too, I guess they make their own springs.

thanks
97 Red XJ, 4.5", 31" mud's, ARB front, 9500lb winch, bushwhacker's, warn sliders, HnT SYE and CV drive shaft - written off and sold for parts :(

Offline nickcoleman9

  • Baby Wheeler
  • Posts: 77
Re: shock lower bushing
« Reply #3 on: December 04, 2009, 09:48:35 AM »
ive always had good luck at mopac on 16th as well like 5 bucks a set and in stock it seems just need inner and outer measurements

Offline hps4evr

  • Administrator
  • Talks waaay too much!
  • Posts: 2959
Re: shock lower bushing
« Reply #4 on: December 04, 2009, 06:00:45 PM »
see, i understand the use of KY in this application. but why is it that KY is the first to be used? i have far more experience and very good luck with astro-glide. it may not be as easy to find as KY, but its a much better performer. it leaves a longer lasting film of lubricant to help penetration of the rubber bushing into the shock eye. FYI, be sure to clean the eye first, nobody likes lubing the rubber and forcing it into a dirty eye...
YJ=Y’all Jealous

Offline Zombie

  • UberWheeler
  • Posts: 398
  • Jeff the Zombie Jeep
Re: shock lower bushing
« Reply #5 on: December 04, 2009, 06:25:47 PM »
see, i understand the use of KY in this application. but why is it that KY is the first to be used? i have far more experience and very good luck with astro-glide. it may not be as easy to find as KY, but its a much better performer. it leaves a longer lasting film of lubricant to help penetration of the rubber bushing into the shock eye. FYI, be sure to clean the eye first, nobody likes lubing the rubber and forcing it into a dirty eye...

this started as a nice simple question and you go and do this, real nice. haha ;D
97 Red XJ, 4.5", 31" mud's, ARB front, 9500lb winch, bushwhacker's, warn sliders, HnT SYE and CV drive shaft - written off and sold for parts :(

Offline mike s

  • UberWheeler
  • Posts: 361
  • Good times!
Re: shock lower bushing
« Reply #6 on: December 05, 2009, 01:07:55 AM »
Astro-glide is...

Try silicone brake lube for bushing install, won't disolve rubber bushings and stays around awhile to prevent squeeks, or if it squeeks too much there is always astro-glide...
'94 YJ, 2.5" RE, 1"BL on 35"s, 8.8 w 4.88
oldEnuff2NObetter

but still can't help myself