Calgary Jeep Association

« previous next »
Pages: [1]   Go Down

Author Topic: 18 Volt Impact Drivers ?  (Read 2035 times)

0 Members and 1 Guest are viewing this topic.

Offline keener

  • Budget Lift
  • Posts: 254
18 Volt Impact Drivers ?
« on: April 11, 2010, 10:45:11 AM »
Has anyone had any luck with these ?
I bought the $130.00 model at Crappy Tire yesterday, and it couldn't even break out wheel nuts which I hand torqued to 90ft-lbs.
This is suprising, considering it supposedly is good for 200 ft-lbs.
Logged
'04 Unlimited with a few mods. SOLD
98 XJ with a few mods. SOLD
02 Sahara with lots of Mods.

Offline Waytec

  • Talks waaay too much!
  • Posts: 1972
  • not all there
Re: 18 Volt Impact Drivers ?
« Reply #1 on: April 11, 2010, 11:08:20 AM »
I have the 3/8 snap-on one and A friend at work has a 1/2 snap-on and they will twist your hand off.
Some guys got the CT 1/2 and my 3/8 has more torque.
Logged
Why does your Jeep say Toyota on it?
The obstacle is the path.

Offline Fredduck

  • That CB Yapper
  • Posts: 607
  • RIDE ON
Re: 18 Volt Impact Drivers ?
« Reply #2 on: April 11, 2010, 02:37:05 PM »
i bought the 1/2 Snap on.
Tightening lug nuts, 3 bangs of the impact is 120 ft/lbs (tested with a torque wrench)
Advertised 1100 ft/lb break away torque ( un-do)
Expensive but worth the cash.
Logged
3.9 CTD - 7000R4  NP241c SSYE, Dana 44.  9 inch, 4.10's  and 37's

Offline yyc_tbird_sc

  • Budget Lift
  • Posts: 222
Re: 18 Volt Impact Drivers ?
« Reply #3 on: April 11, 2010, 11:31:03 PM »
I've got the DeWalt 18v 1/2" impact...it works great!! Especially for making other guys in pick-n-pull jealous. LOL

The Li-ION battery is well worth the money as it runs longer and there is none of the Ni-CAD battery problems.
Logged
-'97 Ranger w/ 4" lift, 33" MTZ's, 4.56's, and some new sheet metal
-'89 Thunderbird SC - 285HP, 392ft/lbs [email protected]

Offline parabs

  • That CB Yapper
  • Posts: 504
Re: 18 Volt Impact Drivers ?
« Reply #4 on: April 12, 2010, 03:05:59 PM »
Quote from: keener on April 11, 2010, 10:45:11 AM
Has anyone had any luck with these ?
I bought the $130.00 model at Crappy Tire yesterday, and it couldn't even break out wheel nuts which I hand torqued to 90ft-lbs.
This is suprising, considering it supposedly is good for 200 ft-lbs.

I bought an older model of the can tire impact that was supposed be to good for 100 or so lb-ft.  Not even close, maybe 65, maybe...I haven't ever heard good things about the CT impacts after I bought mine.
Logged
2000 TJ Sahara - Sold
2006 Lincoln Mark LT - Bassani Exhaust
2007 Harley Davidson F150 - Nothing to note.
Pages: [1]   Go Up
« previous next »