Calgary Jeep Association

Author Topic: grand lift height  (Read 1129 times)

0 Members and 1 Guest are viewing this topic.

Offline heep-a-lop

  • UberWheeler
  • Posts: 361
  • EMF WHORE
    • EMF Rod Ends And Steering Components
grand lift height
« on: November 30, 2011, 12:18:48 PM »
okay trying to make some final decisions here...

one being lift height?

what have u guys Ran?


liked ? disliked?

i am thinkin 4.5

and what sp[ring if u where gonna do it all again would u run...

its short arm adjustable uppers fornt and rear and adjustable trck bars

Offline WhiteOut

  • Talks waaay too much!
  • Posts: 1885
Re: grand lift height
« Reply #1 on: November 30, 2011, 12:34:50 PM »
4.5" Rubicon Express springs, 4.5" is the edge of a well behaved street vehicle
Front IRO long arms
Rear adjustable upper and lower arms
Front and rear adjustable trackbars
Bilstein 5125 shocks ~28" extended
JKS Disconnects

Don't bother with IRO steering, the heims squeak like a mofo and they wear out ridiculously fast.

If you go 7" swap the rear short arms for long arms, Clayton 7" coils and longer shocks

Under 4" get shorter shocks and use adjustable upper and lower front control arms

I have run 2" BB with only longer shocks, 3.5" on only lower control arms, 3.5" on all adjustables, 5.5" on long arms and rear adjustables. Always used RE springs, those and Clayton are the best bang for the buck at that height (at least on a Grand). When I get my rear bumper I'll run a 7" spring to get 6" of overall lift.
« Last Edit: November 30, 2011, 12:41:49 PM by WhiteOut »

Offline heep-a-lop

  • UberWheeler
  • Posts: 361
  • EMF WHORE
    • EMF Rod Ends And Steering Components
Re: grand lift height
« Reply #2 on: November 30, 2011, 12:58:46 PM »
i was lookin at kevins offroad tube bumper  anyone run on? how heavy?

Offline WhiteOut

  • Talks waaay too much!
  • Posts: 1885
Re: grand lift height
« Reply #3 on: November 30, 2011, 01:02:59 PM »
Front or rear

Offline heep-a-lop

  • UberWheeler
  • Posts: 361
  • EMF WHORE
    • EMF Rod Ends And Steering Components
Re: grand lift height
« Reply #4 on: November 30, 2011, 01:11:13 PM »
think both to be honest not right away by any means but summer time

Offline JackstandJohnny

  • Talks waaay too much!
  • Posts: 4727
  • where Jeeps go to die
Re: grand lift height
« Reply #5 on: November 30, 2011, 01:40:29 PM »
3" is good.

your tires will look stoopid if you lift it any higher. then you'll need 33s.  ;)
~ rescue green JKUR on 35s.  typical rubicon build

Offline priceless

  • Winch Wench
  • Posts: 40
Re: grand lift height
« Reply #6 on: November 30, 2011, 02:06:33 PM »
Yep. I've done a few heights. My fav is around 5.5'. Your gonna spend a few $$ getting your shafts, steering ect where you like it. But Johnny's right...31's are not enough after 3'. If i was going to change springs i would go with IRO or RE. Again thats just one guys ideas.  ;)

Offline cLAY

  • Talks waaay too much!
  • Posts: 2377
Re: grand lift height
« Reply #7 on: November 30, 2011, 07:00:46 PM »
8" and Claytons Long Arms.

Very well built/ stout kit. Expensive. Mine isn't street friendly but thats probably more to do with the 36" bias ply tires and homebuilt diffs and steering.

Next build is a 5.9 ZJ that will be 100% streetable, 3-4" of lift and 31-33s.
..

'93 ZJ, 5.2L, lifted/locked/36s..<gone>
'98 5.9er 4.10s,locked,LA,WJ knuckles

Offline heep-a-lop

  • UberWheeler
  • Posts: 361
  • EMF WHORE
    • EMF Rod Ends And Steering Components
Re: grand lift height
« Reply #8 on: December 05, 2011, 04:52:57 AM »
okay after thinking some more i think i am going to go with a 4.5 coil and with bumpers and roof rack and such should be about 3.5 lift....

alot like a expedition rig and if it doesn t sag to much will put 33's on it...

Offline priceless

  • Winch Wench
  • Posts: 40
Re: grand lift height
« Reply #9 on: December 06, 2011, 08:48:39 PM »
Thats a very street & trail friendly rout. I think you'll like.