Calgary Jeep Association

« previous next »
Pages: [1]   Go Down

Author Topic: what to do  (Read 2177 times)

0 Members and 1 Guest are viewing this topic.

Offline Rubi03 jef

  • Talks waaay too much!
  • Posts: 1918
  • she never understands
what to do
« on: March 15, 2010, 08:35:36 PM »
alright boys and girls

need some advice ..

i need to do gears and bearings in both front and rear diffs
as well as front and rear axles

now my question is i dont have the 1800$ to do it all in one shot

i figure i should do front and rear gears and bearings and front shafts   leave the rear ones for a month or so

or do i suck it up and do them all at once and be tight as BEEP for a month or so
Logged
04 rubicon <4'' X series RC lift, 1.25'' RC body lift, 1'' RC MML, CV rear drive shaft,  Stubby front bumper, CB,35 MTZ" ,Hi Lifter 54'',LED tail lights , flat fenders, LED front Flasher, half doors, Light force spots, and CDN M101 custom Military trailer

Offline dac

  • That CB Yapper
  • Posts: 516
Re: what to do
« Reply #1 on: March 15, 2010, 09:03:55 PM »
I'd either wait till after the next big snow dump or do it all at once.  I'm betting we get one last city stopper before we see spring.
Logged
This is not 'Nam, this is wheeling.  There are rules.

Offline hps4evr

  • Administrator
  • Talks waaay too much!
  • Posts: 2959
Re: what to do
« Reply #2 on: March 15, 2010, 09:14:46 PM »
a month isnt very long. wait the 1 month, then order it all at once. save on shipping or whatever and then you can organize the install time better. instead of taking it all apart twice.
Logged
YJ=Y’all Jealous

Offline Rubi03 jef

  • Talks waaay too much!
  • Posts: 1918
  • she never understands
Re: what to do
« Reply #3 on: March 15, 2010, 10:10:47 PM »
install will be done by my brother

i just dont knwo how much damage im doing in the rear end everything sounds loose and well i know im changing everything out but is there any chance of busting my locker in there or what
Logged
04 rubicon <4'' X series RC lift, 1.25'' RC body lift, 1'' RC MML, CV rear drive shaft,  Stubby front bumper, CB,35 MTZ" ,Hi Lifter 54'',LED tail lights , flat fenders, LED front Flasher, half doors, Light force spots, and CDN M101 custom Military trailer

Offline Mikes off road

  • Budget Lift
  • Posts: 140
Re: what to do
« Reply #4 on: March 17, 2010, 07:40:30 AM »
Sorry to hijack the post but I have a question about gears. I had my gears done about 8 months ago and now I want to install a detriot locker in the rear. Do you think I would have to redo the Backlash or screw around with the Pinion setting at all. I know I should have waited and done them both at the same time but I didn't.
Logged
98 XJ Classic with a Fulltraction 6" lift 35" MTZ on Procomp rims. Locked front and rear with 4.56 gears. Warn bumber with 9000lb winch. Custom built rock rails, rear bumber with sotc, and skid plates.

Offline X-Treme

  • Baby Wheeler
  • Posts: 52
Re: what to do
« Reply #5 on: March 17, 2010, 12:53:07 PM »
Quote from: Mikes off road on March 17, 2010, 07:40:30 AM
Sorry to hijack the post but I have a question about gears. I had my gears done about 8 months ago and now I want to install a detriot locker in the rear. Do you think I would have to redo the Backlash or screw around with the Pinion setting at all. I know I should have waited and done them both at the same time but I didn't.

Yes.
Logged

Offline Bnine

  • Talks waaay too much!
  • Posts: 2572
  • Sticky Fingers
Re: what to do
« Reply #6 on: March 17, 2010, 01:26:29 PM »
Quote from: Mikes off road on March 17, 2010, 07:40:30 AM
Sorry to hijack the post but I have a question about gears. I had my gears done about 8 months ago and now I want to install a detriot locker in the rear. Do you think I would have to redo the Backlash or screw around with the Pinion setting at all. I know I should have waited and done them both at the same time but I didn't.

No Mike, you only have to do the backlash, and carrier bearing preload. Pinion will remain the same.

Not a tough job. Specially if its a 8.25 with the spanners.

Logged
My Mechanic Calgary
Mobile Auto Care
403-483-1083
[email protected]

Offline Bnine

  • Talks waaay too much!
  • Posts: 2572
  • Sticky Fingers
Re: what to do
« Reply #7 on: March 17, 2010, 01:31:32 PM »
Quote from: Rubi03 jef on March 15, 2010, 10:10:47 PM
i just dont knwo how much damage im doing in the rear end everything sounds loose and well i know im changing everything out but is there any chance of busting my locker in there or what

There is a good chance your locker is gone already. Unforunate as that sounds, of all the rubicon diffs I've done, which is probably 50 plus, the only two I've ever seen with internal failures have been blown lockers.

You might want to look at that before making a decision. If your locker is blown you will be getting into 2000$ just repair and replace whats in there. Specially if the locker guts have chewed the gears up.

Logged
My Mechanic Calgary
Mobile Auto Care
403-483-1083
[email protected]

Offline Eagle Jeeper

  • Budget Lift
  • Posts: 286
Re: what to do
« Reply #8 on: March 17, 2010, 04:35:40 PM »
Do it all at once one way or the other  I am not a big fan of being broke so I'd wait a month.  Don't know about the locker but if there is bits of metal floating around in your diff fluid I can't imagine its doing the locker any good
Logged
94 YJj7, AMC360,T176,Dana300(twin stick, Dana 44 4:56, 14 bolt FF welded 4:56, 2 1/2" susp SOA, 38/12.5/15 TSL's, warn 8274,  Custom dash
Pages: [1]   Go Up
« previous next »