Calgary Jeep Association

« previous next »
Pages: [1]   Go Down

Author Topic: MJ / XJ Rockers  (Read 992 times)

0 Members and 1 Guest are viewing this topic.

Offline specialk

  • CJA Executive
  • Talks waaay too much!
  • Posts: 3176
MJ / XJ Rockers
« on: December 07, 2011, 12:21:50 PM »
What size tubing have you used when replacing the rockers on your MJ/XJ?   2x4 or 2x6?

And do you cut out up to the pinch weld?
Logged
04 TJ Rubi

Offline Immortal

  • Talks waaay too much!
  • Posts: 3463
Re: MJ / XJ Rockers
« Reply #1 on: December 07, 2011, 05:32:04 PM »
Cut until there isn't anymore rust. That will be enough to get a 2x6 in mine. You may be able to get away with just a 2x4, though.
And, yes.
Logged
Quote from: w squared on October 26, 2010, 10:44:27 AM
if we were smart with our money we wouldn't own Jeeps.
Here's your cup of STFU... ENJOY!

Offline Tyn Pow

  • Budget Lift
  • Posts: 196
Re: MJ / XJ Rockers
« Reply #2 on: December 07, 2011, 05:34:14 PM »
I used .250 wall 2x6.

I only cut the outside of the stock rocker out which gives enough room to jam in a piece of 2x6 HSS  with a little persuasion.  The stock sheetmetal will hold the slider in place really well, then just weld 'er up and call 'er done.
Logged

Offline TL-Iguana

  • Talks waaay too much!
  • Posts: 1117
  • XJ - The Official TJ Rescue Vehicle
Re: MJ / XJ Rockers
« Reply #3 on: December 07, 2011, 05:35:33 PM »
Ask Dana to send you a picture of how he has just done his... His original set was flush and it didnt seem to look right... On the 2 door now he has left a lip that is welded to the 2x4 box and it looks pretty damn good.
Logged
I did a Google search for "hot trannies" but nothing came up about oil coolers  :o

Worrying too much about mpg with a Jeep is similar to worrying about your sister's virginity. An ok thing to be concerned about but...

'01 XJ on 35s, '11 Jk DD

Offline specialk

  • CJA Executive
  • Talks waaay too much!
  • Posts: 3176
Re: MJ / XJ Rockers
« Reply #4 on: December 07, 2011, 08:52:34 PM »
Thank you gents.
Logged
04 TJ Rubi

Offline XJHERO

  • Talks waaay too much!
  • Posts: 2041
  • Soberphobic
Re: MJ / XJ Rockers
« Reply #5 on: December 09, 2011, 09:26:45 PM »
i forget and its too far away for me to check.
what ever you can get ahold of that works, i know tootc could not find the same size as i used but his turned out great.
i think .25 wall is way over kill. mine is .125 and i have kicked the crap out of it with no dents or bends.
Its a shity job but when its done its super tuff.
Logged
Like ivry soap....pure as frack
DD
Get at me Wolf

Offline Tyn Pow

  • Budget Lift
  • Posts: 196
Re: MJ / XJ Rockers
« Reply #6 on: December 10, 2011, 12:45:19 AM »
Quote from: XJHERO on December 09, 2011, 09:26:45 PM
i think .25 wall is way over kill. mine is .125 and i have kicked the crap out of it with no dents or bends.
Its a shity job but when its done its super tuff.

Agreed.  I only used 1/4" cause I was/am planning on using the sliders as air tanks once I finish my ghetto homebrew OBA and wanted some "erosion allowance"

I'm sure 0.125" would work well
Logged
Pages: [1]   Go Up
« previous next »