Calgary Jeep Association

« previous next »
Pages: [1]   Go Down

Author Topic: damaged trackbar bracket on axle.  (Read 1289 times)

0 Members and 1 Guest are viewing this topic.

Offline Zombie

  • UberWheeler
  • Posts: 398
  • Jeff the Zombie Jeep
damaged trackbar bracket on axle.
« on: April 13, 2010, 09:39:25 PM »
So I discovered that I have stretched out the hole on the axle that the track-bar bolts to on to.

I now need to have this repaired somehow.

who should I see about this?
hopefully I can support a CJA guys shop or something like that, or just a good shop that you would recommend that would be able to repair it for me.

I would assume it would entail some welding or something like that. but I do not have the skills to do this right now.

thanks,

Steve
Logged
97 Red XJ, 4.5", 31" mud's, ARB front, 9500lb winch, bushwhacker's, warn sliders, HnT SYE and CV drive shaft - written off and sold for parts :(

Offline specialk

  • CJA Executive
  • Talks waaay too much!
  • Posts: 3176
Re: damaged trackbar bracket on axle.
« Reply #1 on: April 13, 2010, 09:43:56 PM »
Talk Jay (LemonAid Jay) at Chanda Motors.  He can do the welding for you.
Logged
04 TJ Rubi

Offline frenchy

  • Talks waaay too much!
  • Posts: 1417
Re: damaged trackbar bracket on axle.
« Reply #2 on: April 13, 2010, 09:47:44 PM »
Quote from: specialk on April 13, 2010, 09:43:56 PM
Talk Jay (LemonAid Jay) at Chanda Motors.  He can do the welding for you.

Yip, fill in ovaled hole, then have him weld washers on the bracket so it doesn't happen again.
Logged
Jeep
With stuff

Offline Zombie

  • UberWheeler
  • Posts: 398
  • Jeff the Zombie Jeep
Re: damaged trackbar bracket on axle.
« Reply #3 on: April 14, 2010, 12:01:40 AM »
sweet.
I will drop him a line tomorrow I think.

thanks
steve
Logged
97 Red XJ, 4.5", 31" mud's, ARB front, 9500lb winch, bushwhacker's, warn sliders, HnT SYE and CV drive shaft - written off and sold for parts :(

Offline Mikes off road

  • Budget Lift
  • Posts: 140
Re: damaged trackbar bracket on axle.
« Reply #4 on: April 14, 2010, 06:35:40 AM »
On my old Xj I was able to weld a thick washer over the worn out hole. Seemed to work till I swapped Jeeps.
Logged
98 XJ Classic with a Fulltraction 6" lift 35" MTZ on Procomp rims. Locked front and rear with 4.56 gears. Warn bumber with 9000lb winch. Custom built rock rails, rear bumber with sotc, and skid plates.

Offline Bnine

  • Talks waaay too much!
  • Posts: 2572
  • Sticky Fingers
Re: damaged trackbar bracket on axle.
« Reply #5 on: April 14, 2010, 09:24:36 AM »
You can do a washer if you have to, but a small (1/2") sleeve of tube welded to the end of the bracket is a better fix.

Washers are relatively soft, and at best are usually a temporary fix. If you use tube, it wont wallow. More work, but worth the effort.
Logged
My Mechanic Calgary
Mobile Auto Care
403-483-1083
[email protected]
Pages: [1]   Go Up
« previous next »