Calgary Jeep Association

« previous next »
Pages: [1]   Go Down

Author Topic: Pitman arm nut/washer size?  (Read 995 times)

0 Members and 3 Guests are viewing this topic.

Offline Rodzilla

  • Winch Wench
  • Posts: 29
Pitman arm nut/washer size?
« on: June 08, 2010, 04:39:57 PM »
I purchased a new steering box and when I gave them my old one for the core charge they also got my pitman arm with it since I couldn't remove it (to lazy was more like it), and since I bought a new drop pitman arm I really didn't care. But now my problem is finding a new bolt/washer that will work. Does anyone know the grade/thread/size of nut and where to find it and a hardened washer? Thanks in advance for any input. Cheers
« Last Edit: June 08, 2010, 04:41:51 PM by Rodzilla »
Logged

Offline FiEND

  • Talks waaay too much!
  • Posts: 3775
  • Wrecking Ball
Re: Pitman arm nut/washer size?
« Reply #1 on: June 08, 2010, 05:42:11 PM »
google says 1 - 5/16"

you need breaker bar for sure and some penetrating oil would help.  take them to pick n pull and you can even get spares. 
Logged
1Wide2High
ILV2FRT
'97 TJ [sold]
'17 JK Rubicon

Offline Rodzilla

  • Winch Wench
  • Posts: 29
Re: Pitman arm nut/washer size?
« Reply #2 on: June 08, 2010, 06:57:14 PM »
Quote from: FiEND on June 08, 2010, 05:42:11 PM
google says 1 - 5/16"

you need breaker bar for sure and some penetrating oil would help.  take them to pick n pull and you can even get spares. 

Actually I'm looking for what the bolt size is on the pitman arm. Like what thread count is and if its course/fine and the diameter of it. Was going to see if I can find a nut to match at a bolt supply store. Is there a washer? I can't remember. Thanks.
Logged

Offline Bnine

  • Talks waaay too much!
  • Posts: 2572
  • Sticky Fingers
Re: Pitman arm nut/washer size?
« Reply #3 on: June 09, 2010, 09:54:29 AM »
Big ol lock washer on there.

Caliper the shaft on your box for the size, and its definately fine thread. Pretty sure its around 7/8's, but you had best check to make sure.
Logged
My Mechanic Calgary
Mobile Auto Care
403-483-1083
[email protected]

Offline Rodzilla

  • Winch Wench
  • Posts: 29
Re: Pitman arm nut/washer size?
« Reply #4 on: June 09, 2010, 11:15:24 AM »
Yes ^^^^^^^ its a 7/8 14 pitch(fine) thread. Going to go find one now  :)
Logged

Offline jpthing

  • UberWheeler
  • Posts: 389
  • I like things with wheels.
Re: Pitman arm nut/washer size?
« Reply #5 on: June 12, 2010, 10:46:44 AM »
I would be reluctant to use anything but the correct factory part or something that was very high quality. I would get one pff any jeep at PNP.

A word to the wise:`anytime you remove the pitman arm, check the tourque on the nut once and a while for a few weeks.  My buddy`s jeep loosened up when set with a torque wrench to the correct tourqe, I usually tighten mine more or less as tight as I can get it, use blue threadlock and check it for a few weeks.

This is not something you want coming off while you`re driving!!
Logged
'97 TJ, 5" lift, 35's "Sprout"
'95 Xj, 4" lift, 33's Sold to the Bagman
'10 JK unlimited

"Whether you think you can or think you can't...you're right."
-Henry Ford

I'm finally over the Jeep bike debacle..

Offline Rodzilla

  • Winch Wench
  • Posts: 29
Re: Pitman arm nut/washer size?
« Reply #6 on: June 13, 2010, 07:57:29 PM »
I'm using a grade 8 nut and washer. I will check the torque periodically like you suggest. I trailer my rig to and from the bush, no hi-speeds to worry about stuff coming off. Probably lucky if I've seen of 30km/hr yet.
Logged
Pages: [1]   Go Up
« previous next »