Calgary Jeep Association

« previous next »
Pages: [1]   Go Down

Author Topic: top bellhousing bolts on jeep YJ/wrangler  (Read 1814 times)

0 Members and 1 Guest are viewing this topic.

Offline JackstandJohnny

  • Talks waaay too much!
  • Posts: 4727
  • where Jeeps go to die
top bellhousing bolts on jeep YJ/wrangler
« on: February 12, 2015, 12:42:32 PM »
instead of putting the reverse torx back in i'm going to use real bolts.

having a brainfart though. if i recall it is a normal 3/8" bolt 1 3/4" long correct? 

Logged
~ rescue green JKUR on 35s.  typical rubicon build

Offline Vinman

  • CJA Executive
  • Talks waaay too much!
  • Posts: 2237
Re: top bellhousing bolts on jeep YJ/wrangler
« Reply #1 on: February 12, 2015, 12:54:20 PM »
Quote from: JackstandJohnny on February 12, 2015, 12:42:32 PM
instead of putting the reverse torx back in i'm going to use real bolts.

having a brainfart though. if i recall it is a normal 3/8" bolt 1 3/4" long correct? 



I thought it was 3/8-16 x 1-1/2 in my 05 TJ with the 6 spd
Logged
/l ,[____],
 l---L -OlllllllO-
 ()_)-()_)-o-)_)

Quote from: Bnine link=topic=25904.msg162940#msg162940      date=1341881306
. 
 Resident prick is my job and it took me ten years to earn that title

Offline JackstandJohnny

  • Talks waaay too much!
  • Posts: 4727
  • where Jeeps go to die
Re: top bellhousing bolts on jeep YJ/wrangler
« Reply #2 on: February 12, 2015, 01:30:17 PM »
right. 3/8" 16thread.   those bastards were in there so tight i needed to use a breaker bar to get em undone. 

Logged
~ rescue green JKUR on 35s.  typical rubicon build

Offline Grease Nipple

  • Budget Lift
  • Posts: 132
Re: top bellhousing bolts on jeep YJ/wrangler
« Reply #3 on: February 12, 2015, 04:51:22 PM »
Yes, but you left out the part that you needed the breakerbar after you were turning the wrench the wrong way.
Logged

Offline hps4evr

  • Administrator
  • Talks waaay too much!
  • Posts: 2959
Re: top bellhousing bolts on jeep YJ/wrangler
« Reply #4 on: February 12, 2015, 07:15:54 PM »
Quote from: Grease Nipple on February 12, 2015, 04:51:22 PM
Yes, but you left out the part that you needed the breakerbar after you were turning the wrench the wrong way.

Jackstand Johnny strikes again! Rehehehehe...;)
Logged
YJ=Y’all Jealous

Offline Bnine

  • Talks waaay too much!
  • Posts: 2572
  • Sticky Fingers
Re: top bellhousing bolts on jeep YJ/wrangler
« Reply #5 on: February 17, 2015, 01:08:27 PM »
Straight shot with an impact if you let the tail hang down.
Logged
My Mechanic Calgary
Mobile Auto Care
403-483-1083
[email protected]

Offline JackstandJohnny

  • Talks waaay too much!
  • Posts: 4727
  • where Jeeps go to die
Re: top bellhousing bolts on jeep YJ/wrangler
« Reply #6 on: February 20, 2015, 09:51:59 AM »
ians just being funny,

but i did have to put my lil' breaker on it.  just an awkward position couldn't get any leverage.  popped them out, replaced with the proper bolts so next time the slave cylinder craps the bed it won't be that much of a hassle.
Logged
~ rescue green JKUR on 35s.  typical rubicon build
Pages: [1]   Go Up
« previous next »