Calgary Jeep Association

« previous next »
Pages: [1]   Go Down

Author Topic: Air/Hydraulic vertical bender  (Read 836 times)

0 Members and 2 Guests are viewing this topic.

KrossLoch Fab

  • Guest
Air/Hydraulic vertical bender
« on: May 19, 2009, 01:06:17 PM »
At my shear stupidity, I still cant post pics on here!
http://edmontonjeep.com/forum/viewtopic.php?f=28&t=7316
Logged

Offline Immortal

  • Talks waaay too much!
  • Posts: 3463
Re: Air/Hydraulic vertical bender
« Reply #1 on: May 19, 2009, 07:26:59 PM »




Logged
Quote from: w squared on October 26, 2010, 10:44:27 AM
if we were smart with our money we wouldn't own Jeeps.
Here's your cup of STFU... ENJOY!

KrossLoch Fab

  • Guest
Re: Air/Hydraulic vertical bender
« Reply #2 on: May 19, 2009, 07:31:19 PM »
Thanks T!!!
Logged

Offline Immortal

  • Talks waaay too much!
  • Posts: 3463
Re: Air/Hydraulic vertical bender
« Reply #3 on: May 19, 2009, 07:33:01 PM »
no prob C.
Logged
Quote from: w squared on October 26, 2010, 10:44:27 AM
if we were smart with our money we wouldn't own Jeeps.
Here's your cup of STFU... ENJOY!

Offline esi

  • That CB Yapper
  • Posts: 633
Re: Air/Hydraulic vertical bender
« Reply #4 on: May 19, 2009, 10:27:11 PM »
Are you selling them?
Logged
Formerly of Boots & Boost Inc
Back farming and fabricating again.

KrossLoch Fab

  • Guest
Re: Air/Hydraulic vertical bender
« Reply #5 on: May 19, 2009, 11:05:57 PM »
Quote from: esi on May 19, 2009, 10:27:11 PM
Are you selling them?
This one I made for my shop. But I could build and sell if there were interest.
Logged

Offline esi

  • That CB Yapper
  • Posts: 633
Re: Air/Hydraulic vertical bender
« Reply #6 on: May 19, 2009, 11:39:20 PM »
How much would the PT105 cost, with 1.5" dies?
Logged
Formerly of Boots & Boost Inc
Back farming and fabricating again.

KrossLoch Fab

  • Guest
Re: Air/Hydraulic vertical bender
« Reply #7 on: May 20, 2009, 10:33:30 AM »
Quote from: esi on May 19, 2009, 11:39:20 PM
How much would the PT105 cost, with 1.5" dies?
Set up air/hyd?
Logged

Offline esi

  • That CB Yapper
  • Posts: 633
Re: Air/Hydraulic vertical bender
« Reply #8 on: May 20, 2009, 06:04:48 PM »
No air/hydro just a bender, or may be even just the dyes alone. Craig said you were set up to bring in the PT products at a cheaper price than a guy off the street gets. If you could check some prices and PM them to me when you get spare time, that would be appreciated. No big rush, just when you have a spare moment
Logged
Formerly of Boots & Boost Inc
Back farming and fabricating again.

KrossLoch Fab

  • Guest
Re: Air/Hydraulic vertical bender
« Reply #9 on: May 27, 2009, 12:39:01 PM »
Quote from: esi on May 20, 2009, 06:04:48 PM
No air/hydro just a bender, or may be even just the dyes alone. Craig said you were set up to bring in the PT products at a cheaper price than a guy off the street gets. If you could check some prices and PM them to me when you get spare time, that would be appreciated. No big rush, just when you have a spare moment

I will check it out for you!

on a side note; with the longer ram I get 55* on the first stroke, a quick pin cahnge and 90* is no problem. Gotta love when something else does all the work for you!
Logged
Pages: [1]   Go Up
« previous next »