Calgary Jeep Association

« previous next »
Pages: [1]   Go Down

Author Topic: where to get spring perches  (Read 1343 times)

0 Members and 1 Guest are viewing this topic.

Offline morerpmfred

  • Talks waaay too much!
  • Posts: 1604
where to get spring perches
« on: April 10, 2011, 05:27:12 PM »
For an xj. Crawling underneath today , looking for some mystery noises i found some rear spring perches that have gone flatter and rounded in all the wrong places. Do not know what happenned , has never been down a couple thousand miles of ugly washboard road at excessive speed  ;D  Or offroad  ;D Where do you get new spring perches ?
Logged

Offline Rookie

  • CJA Members
  • That CB Yapper
  • Posts: 845
  • build it, break it, rebuild it better
Re: where to get spring perches
« Reply #1 on: April 10, 2011, 09:46:38 PM »
Standens will have them sitting on the shelf and way cheaper than everywhere else last time i had to get some
Logged
TJ with some stuff

Offline stroker sahara

  • UberWheeler
  • Posts: 361
Re: where to get spring perches
« Reply #2 on: April 10, 2011, 10:40:55 PM »
I have some that I make CNC plasma and CNC brake. They are 7 " long for anti-wrap and have three holes for mounting axle center or forward/back 1".

$25/pr

Available for 2.75, 3.0, and 3.25" axle tubes
Logged
If you want to run with the big dogs you have to be able to pee in the tall grass.


1989 YJ SOA, 36" SX, 4.6 Stroker...

Offline Bnine

  • Talks waaay too much!
  • Posts: 2572
  • Sticky Fingers
Re: where to get spring perches
« Reply #3 on: April 11, 2011, 07:47:08 AM »
Quote from: stroker sahara on April 10, 2011, 10:40:55 PM
I have some that I make CNC plasma and CNC brake. They are 7 " long for anti-wrap and have three holes for mounting axle center or forward/back 1".

$25/pr

Available for 2.75, 3.0, and 3.25" axle tubes

Those would be the way to go.
Logged
My Mechanic Calgary
Mobile Auto Care
403-483-1083
[email protected]

Offline XJHERO

  • Talks waaay too much!
  • Posts: 2041
  • Soberphobic
Re: where to get spring perches
« Reply #4 on: April 11, 2011, 08:20:25 AM »
Quote from: stroker sahara on April 10, 2011, 10:40:55 PM
I have some that I make CNC plasma and CNC brake. They are 7 " long for anti-wrap and have three holes for mounting axle center or forward/back 1".

$25/pr

Available for 2.75, 3.0, and 3.25" axle tubes
wish i knew about these before the last  3 shity pairs i got from standens
Logged
Like ivry soap....pure as frack
DD
Get at me Wolf

Offline rangerdanger

  • Budget Lift
  • Posts: 167
Re: where to get spring perches
« Reply #5 on: April 11, 2011, 09:34:31 AM »
I run the ones that stroker sahara makes and they are good quality, heavy duty stuff. Plus the ability to adjust your wheelbase slightly is nice.  :)
Logged
Lethbridge Coulee Kruzer

Offline morerpmfred

  • Talks waaay too much!
  • Posts: 1604
Re: where to get spring perches
« Reply #6 on: April 11, 2011, 10:07:29 AM »
I would like to get a set of these from stroker sahara. I have a Dana 35 so I think I need the 2.75 size. My cell number is 470 2942 Andy.
Logged

Offline morerpmfred

  • Talks waaay too much!
  • Posts: 1604
Re: where to get spring perches
« Reply #7 on: April 16, 2011, 05:08:19 PM »
Thank you Scott for the spring perchs. They are clean and very stout , a very good buy.
Logged
Pages: [1]   Go Up
« previous next »