Calgary Jeep Association

« previous next »
Pages: [1]   Go Down

Author Topic: Pinion seal, yoke holder  (Read 1156 times)

0 Members and 1 Guest are viewing this topic.

Offline GoChris

  • Budget Lift
  • Posts: 105
Pinion seal, yoke holder
« on: March 25, 2019, 03:23:34 PM »
I am trying to replace my front pinion seal, but can't get the nut off. Does anyone have a yoke holder I could borrow so I can hopefully remove the nut?
Logged

Offline Vinman

  • CJA Executive
  • Talks waaay too much!
  • Posts: 2237
Re: Pinion seal, yoke holder
« Reply #1 on: March 25, 2019, 05:31:15 PM »
Put the front wheels on the ground, ebrake on and in 4 low.

Are you sure you need to replace the seal?, last Summer my rear pinion started leaking badly and it turned out to be a plugged axle vent line, cleared the gunk off the end and it hasn’t leaked since
Logged
/l ,[____],
 l---L -OlllllllO-
 ()_)-()_)-o-)_)

Quote from: Bnine link=topic=25904.msg162940#msg162940      date=1341881306
. 
 Resident prick is my job and it took me ten years to earn that title

Offline GoChris

  • Budget Lift
  • Posts: 105
Re: Pinion seal, yoke holder
« Reply #2 on: March 25, 2019, 06:24:04 PM »
Quote from: Vinman on March 25, 2019, 05:31:15 PM
Put the front wheels on the ground, ebrake on and in 4 low.

Are you sure you need to replace the seal?, last Summer my rear pinion started leaking badly and it turned out to be a plugged axle vent line, cleared the gunk off the end and it hasn’t leaked since

I'll check the vent line, and I had the wheels on the ground and someone standing on the brakes, no go.
Logged

Offline Vinman

  • CJA Executive
  • Talks waaay too much!
  • Posts: 2237
Re: Pinion seal, yoke holder
« Reply #3 on: March 25, 2019, 08:21:17 PM »
You could always stick a couple of big screwdrivers or prybars through the axle u-joints
Logged
/l ,[____],
 l---L -OlllllllO-
 ()_)-()_)-o-)_)

Quote from: Bnine link=topic=25904.msg162940#msg162940      date=1341881306
. 
 Resident prick is my job and it took me ten years to earn that title

Offline Jrama

  • That CB Yapper
  • Posts: 923
Re: Pinion seal, yoke holder
« Reply #4 on: March 25, 2019, 09:07:42 PM »
Pipe wrench on yolk it will Jam itself on the upper control arm or exhaust etc.

Used that technique many times.
Logged

Offline specialk

  • CJA Executive
  • Talks waaay too much!
  • Posts: 3176
Re: Pinion seal, yoke holder
« Reply #5 on: March 27, 2019, 05:29:17 PM »
Quote from: Jrama on March 25, 2019, 09:07:42 PM
Pipe wrench on yolk it will Jam itself on the upper control arm or exhaust etc.

Used that technique many times.

X2
Logged
04 TJ Rubi

Offline SwampSinger

  • CJA Members
  • Talks waaay too much!
  • Posts: 6172
  • Baconator
    • mmmmm-bacon
Re: Pinion seal, yoke holder
« Reply #6 on: March 28, 2019, 03:54:42 PM »
build a tool.... 

Logged

Offline Picha

  • Stocker
  • Posts: 1
Re: Pinion seal, yoke holder
« Reply #7 on: April 13, 2019, 04:04:54 AM »
Quote from: Jrama on March 25, 2019, 09:07:42 PM
Pipe wrench on yolk it will Jam itself on the upper control arm or exhaust etc.

Used that technique many times.

Do you have to worry about breaking something if you apply too much force while doing this?
Logged

Offline Jrama

  • That CB Yapper
  • Posts: 923
Re: Pinion seal, yoke holder
« Reply #8 on: April 16, 2019, 01:17:06 PM »
Quote from: Picha on April 13, 2019, 04:04:54 AM
Do you have to worry about breaking something if you apply too much force while doing this?

Common sense applies
Logged
Pages: [1]   Go Up
« previous next »