Calgary Jeep Association

« previous next »
Pages: [1] 2   Go Down

Author Topic: Another TJ Cage build  (Read 4321 times)

0 Members and 2 Guests are viewing this topic.

Offline Brink

  • UberWheeler
  • Posts: 445
Another TJ Cage build
« on: May 07, 2007, 10:24:00 PM »
I have been working on my cage the last while .  It's now all tacked and ready to finish weld.  Only thing left is seat mounts, throw the tube in for frame tie in's (plates are bolted both sides of the floor already) and the grab handles from the A to the spreader over the door.  The handles should reinforce that joint nicely.   Sucks that I ran out of tube today.












Who'd have thought 100' wasn't enough?
Logged

Offline dubbleJs

  • Talks waaay too much!
  • Posts: 1330
Another TJ Cage build
« Reply #1 on: May 07, 2007, 11:42:29 PM »
Great work man!
Logged
'91 XJ - 3" procrap - cutout for 33" MT's  - More and more dents every run...Sold.
'98 XJ - Lifted, locked and lovin' it

Offline Spinalguy

  • Talks waaay too much!
  • Posts: 2759
    • http://www.spinalguy.com
Another TJ Cage build
« Reply #2 on: May 08, 2007, 05:14:54 PM »
Nice stuff Eric.  8)
Logged
sent from my old school rotary dial phone.

Offline kenny kustom

  • Budget Lift
  • Posts: 158
Another TJ Cage build
« Reply #3 on: May 08, 2007, 07:31:39 PM »
GAS TANK?
Logged

Offline SwampSinger

  • CJA Members
  • Talks waaay too much!
  • Posts: 6172
  • Baconator
    • mmmmm-bacon
Another TJ Cage build
« Reply #4 on: May 08, 2007, 09:21:27 PM »
looking really good Eric  8) !!! nice work!!....
Logged

Offline Brink

  • UberWheeler
  • Posts: 445
Another TJ Cage build
« Reply #5 on: May 08, 2007, 09:38:31 PM »
Quote from: "kenny kustom"
GAS TANK?



Sorry buddy.










And some from the bottom....









And one without the tank in....







Next on the to-do list is the whole rear floor/tank cover/inner fenders.  It's all gonna be custom and completely enclosed.

Anything else you need?  Anywhere else you need me to post it  :lol:
Logged

Offline Elsifer

  • Talks waaay too much!
  • Posts: 1089
Another TJ Cage build
« Reply #6 on: May 09, 2007, 10:17:16 AM »
Looking really nice!

Whats with the wishbone in front of the windshield? Do a lot of cages collapse there? You planning on adding some controls in that wedge shaped area?

Really nice cage, I too would have thunk that 100' would be more than enough! Whats the spec on your tube?
Logged
VA6CPL
Jeepless....

Offline GiS

  • That CB Yapper
  • Posts: 641
Another TJ Cage build
« Reply #7 on: May 09, 2007, 10:36:23 AM »
Looks nice man! 100' into that??? You made your own B pillar correct?
Logged

Offline Brink

  • UberWheeler
  • Posts: 445
Another TJ Cage build
« Reply #8 on: May 09, 2007, 02:22:18 PM »
Mostly the center over the dash V helps with lateral collapse of the A pillars.

Yep, new B in it Joe.  Didn't reuse anything from the stock cage.
Logged

Offline Bnine

  • Talks waaay too much!
  • Posts: 2572
  • Sticky Fingers
Another TJ Cage build
« Reply #9 on: May 09, 2007, 08:28:23 PM »
Right on Eric. Looking pretty sharp.

You going to make all your gussets? If not, Evo had some nice ones for 5$ a peice. Nice time savers.

I threw about 8 of them on the CJ sport cage I did. I like em.
Logged
My Mechanic Calgary
Mobile Auto Care
403-483-1083
[email protected]

Offline Brink

  • UberWheeler
  • Posts: 445
Another TJ Cage build
« Reply #10 on: May 09, 2007, 10:03:43 PM »
Don't know if I'm adding any.  The bars all gusset each other on this one.  Other than the a pillar not having it's handle in yet.

See anywhere that needs more triangulation?
Logged

Offline Brink

  • UberWheeler
  • Posts: 445
Another TJ Cage build
« Reply #11 on: May 09, 2007, 10:04:48 PM »
Got any tabs for seatbelts Bill?  I need some and nowhere in Red Deer has any.  I've got enough other little things to do without worrying about cutting out tabs right now.
Logged

Offline Bnine

  • Talks waaay too much!
  • Posts: 2572
  • Sticky Fingers
Another TJ Cage build
« Reply #12 on: May 09, 2007, 10:53:20 PM »
No, I just use old shock bushing, or leaf spring bushing sleeves. Drill and weld through center on the tubing, then bolt them up.

That works.

Tougher if your lower peice is already permanent though.
Logged
My Mechanic Calgary
Mobile Auto Care
403-483-1083
[email protected]

Offline kenny kustom

  • Budget Lift
  • Posts: 158
Another TJ Cage build
« Reply #13 on: May 10, 2007, 07:25:44 AM »
THANKS !!!!!  :!:
Logged

Offline Impact

  • Budget Lift
  • Posts: 191
Re: Another TJ Cage build
« Reply #14 on: April 06, 2015, 09:11:23 AM »
Quote from: Brink on May 07, 2007, 10:24:00 PM
I have been working on my cage the last while .  It's now all tacked and ready to finish weld.  Only thing left is seat mounts, throw the tube in for frame tie in's (plates are bolted both sides of the floor already) and the grab handles from the A to the spreader over the door.  The handles should reinforce that joint nicely.   Sucks that I ran out of tube today.












Who'd have thought 100' wasn't enough?

Dead post bump... Still one of my favourite TJ's. Is the original build thread still somewhere?
Logged
12 Crush JKU Sport
05 Orange TJ Sport-2" BB, 1.25" BL... (1 tons, 39's... Who the fawk really knows!)
92 Red Cherokee Sport-4.5" Rustys Lift, 33's KM2's, Eagle Rims(405k's n still tikkin...) Sold :(
Pages: [1] 2   Go Up
« previous next »