Calgary Jeep Association

« previous next »
Pages: 1 [2]   Go Down

Author Topic: it never ends....  (Read 2872 times)

0 Members and 2 Guests are viewing this topic.

Offline rt01

  • Winch Wench
  • Posts: 40
Re: it never ends....
« Reply #15 on: November 03, 2010, 03:55:10 AM »
I don't think I would try to tap them just replace them, and remember they're metric and the bolts you are using should be too!
 part #   6506 629aa for the 12mm
Logged

Offline jeepjones

  • Budget Lift
  • Posts: 247
Re: it never ends....
« Reply #16 on: November 03, 2010, 03:57:17 AM »
Damn, you have some bad luck modding your rigs!
Logged

Offline GiS

  • That CB Yapper
  • Posts: 641
Re: it never ends....
« Reply #17 on: November 03, 2010, 06:47:02 AM »
Dont bother trying to drill and tap a nutsert, there isn't enough "meat" there. Your best bet is to replace the nutsert, or weld a nut inside the frame rail but I don't think the "windows" are large enough to get a good bead.

Yeah buddy, I've got some extended rear swaybar links, all yours! Just let me know when you want them...they aren't going anywhere.
Logged

Offline GiS

  • That CB Yapper
  • Posts: 641
Re: it never ends....
« Reply #18 on: November 03, 2010, 11:51:43 AM »
And yeah, like the other guy said...could be some mud in your frame. Check mine out  :o

Logged

Offline AV.NINE

  • Talks waaay too much!
  • Posts: 1872
Re: it never ends....
« Reply #19 on: November 03, 2010, 06:08:52 PM »
Thanks anyways joey but too late. Modern had a set in stock for a good price.

I tried to tap the nutserts and failed. They came loose inside the frame. I had some hexicoil so I tapped the frame anyways and installed that. The bolts held and are tight. Kind of sketchy but I have a back up plan.

Note: the drivers side came out just fine.

Plan A - I have some bolts, and I'm going to weld them to a washer then weld a piece of metal (3"s) to that washer. Then tie the end of the bolt to some bailing twine and fish each one through the frame holes. That way alls I have to do is stick a nut on them.

Anyways, here's what she looks like all together:





Just needs an alignment to cure some death wobble.
Logged

Offline Knox

  • That CB Yapper
  • Posts: 649
Re: it never ends....
« Reply #20 on: November 03, 2010, 08:19:02 PM »
looks good, what do you have for axles in there?
Logged
2003 TJ
"Your TJ has the aerodynamics of a brick"
"if you lose the stick, chances are you'll lose the jeep......"

Offline AV.NINE

  • Talks waaay too much!
  • Posts: 1872
Re: it never ends....
« Reply #21 on: November 03, 2010, 08:34:43 PM »
30/35

My real diffs are under construction...
Logged

Offline vantagetes

  • That CB Yapper
  • Posts: 947
  • Edmonton Trail Rated
Re: it never ends....
« Reply #22 on: November 03, 2010, 08:41:34 PM »
Can you hold off on your alignment until your new axles are ready?
Logged

Offline Knox

  • That CB Yapper
  • Posts: 649
Re: it never ends....
« Reply #23 on: November 03, 2010, 08:52:49 PM »
what are you putting in there?
Logged
2003 TJ
"Your TJ has the aerodynamics of a brick"
"if you lose the stick, chances are you'll lose the jeep......"

Offline AV.NINE

  • Talks waaay too much!
  • Posts: 1872
Re: it never ends....
« Reply #24 on: November 03, 2010, 09:36:12 PM »
Quote from: vantagetes on November 03, 2010, 08:41:34 PM
Can you hold off on your alignment until your new axles are ready?

No, they wont be done for 6 months give or take....

Quote from: Knox on November 03, 2010, 08:52:49 PM
what are you putting in there?


Front 9" with Dana 60 outters

Rear 9" with 14 bolt outters
Logged

Offline Rubi03 jef

  • Talks waaay too much!
  • Posts: 1918
  • she never understands
Re: it never ends....
« Reply #25 on: November 03, 2010, 11:47:01 PM »
are those 35   13.5   

looking good .. thats alot of axle for a short arm
Logged
04 rubicon <4'' X series RC lift, 1.25'' RC body lift, 1'' RC MML, CV rear drive shaft,  Stubby front bumper, CB,35 MTZ" ,Hi Lifter 54'',LED tail lights , flat fenders, LED front Flasher, half doors, Light force spots, and CDN M101 custom Military trailer

Offline AV.NINE

  • Talks waaay too much!
  • Posts: 1872
Re: it never ends....
« Reply #26 on: November 04, 2010, 04:55:44 AM »
La will be coming when the wife allows
Logged
Pages: 1 [2]   Go Up
« previous next »