Calgary Jeep Association

« previous next »
Pages: [1]   Go Down

Author Topic: Who machines flywheels in Calgary?  (Read 2394 times)

0 Members and 2 Guests are viewing this topic.

Offline Vinman

  • CJA Executive
  • Talks waaay too much!
  • Posts: 2237
Who machines flywheels in Calgary?
« on: October 17, 2011, 04:16:00 PM »
Anybody know who does this work?
Logged
/l ,[____],
 l---L -OlllllllO-
 ()_)-()_)-o-)_)

Quote from: Bnine link=topic=25904.msg162940#msg162940      date=1341881306
. 
 Resident prick is my job and it took me ten years to earn that title

Offline Spinalguy

  • Talks waaay too much!
  • Posts: 2759
    • http://www.spinalguy.com
Re: Who machines flywheels in Calgary?
« Reply #1 on: October 17, 2011, 04:33:45 PM »
Jim Titmus

phone 403-807-8747 (hope its current, if not let me know)
Use my name as a referral.
Very well respected guy in Calgary
Logged
sent from my old school rotary dial phone.

Offline FiEND

  • Talks waaay too much!
  • Posts: 3775
  • Wrecking Ball
Re: Who machines flywheels in Calgary?
« Reply #2 on: October 18, 2011, 12:50:11 AM »
Don't do it, its bad for the flywheel.   Google will bring up lots of horror stories so no need to post mine.

Logged
1Wide2High
ILV2FRT
'97 TJ [sold]
'17 JK Rubicon

Offline Vinman

  • CJA Executive
  • Talks waaay too much!
  • Posts: 2237
Re: Who machines flywheels in Calgary?
« Reply #3 on: October 18, 2011, 09:04:50 AM »
Quote from: FiEND on October 18, 2011, 12:50:11 AM
Don't do it, its bad for the flywheel.   Google will bring up lots of horror stories so no need to post mine.



I was talking to Steve (Rookie) yesterday and he also said it was a bad idea to machine the TJ flywheel, apparently it's a bit concave and not flat.
I'm just gonna clean it up and install the new clutch.

Thanks
Vince
Logged
/l ,[____],
 l---L -OlllllllO-
 ()_)-()_)-o-)_)

Quote from: Bnine link=topic=25904.msg162940#msg162940      date=1341881306
. 
 Resident prick is my job and it took me ten years to earn that title

Offline cLAY

  • Talks waaay too much!
  • Posts: 2377
Re: Who machines flywheels in Calgary?
« Reply #4 on: October 18, 2011, 10:34:54 AM »
Depends on the clutch you use. Some aftermarket clutchs are designed for a re-surfaced(flat) flywheel.
Logged
..

'93 ZJ, 5.2L, lifted/locked/36s..<gone>
'98 5.9er 4.10s,locked,LA,WJ knuckles

Offline morerpmfred

  • Talks waaay too much!
  • Posts: 1604
Re: Who machines flywheels in Calgary?
« Reply #5 on: October 18, 2011, 10:51:19 AM »
Most shops just use a palm sander with like 60 grit sandpiper and do not spend a lot of time maybe a minute or so get rid of the hotspots and glaze but do the whole surface.
Logged

Offline Vinman

  • CJA Executive
  • Talks waaay too much!
  • Posts: 2237
Re: Who machines flywheels in Calgary?
« Reply #6 on: October 18, 2011, 11:28:40 AM »
Quote from: morerpmfred on October 18, 2011, 10:51:19 AM
Most shops just use a palm sander with like 60 grit sandpiper and do not spend a lot of time maybe a minute or so get rid of the hotspots and glaze but do the whole surface.

That's pretty much what I have planned and I'll be installing an OEM Jeep clutch.

Vince
Logged
/l ,[____],
 l---L -OlllllllO-
 ()_)-()_)-o-)_)

Quote from: Bnine link=topic=25904.msg162940#msg162940      date=1341881306
. 
 Resident prick is my job and it took me ten years to earn that title

Offline Knox

  • That CB Yapper
  • Posts: 649
Re: Who machines flywheels in Calgary?
« Reply #7 on: October 18, 2011, 07:51:58 PM »
hmm good to know, I was not aware of this non flat flywheel issue
Logged
2003 TJ
"Your TJ has the aerodynamics of a brick"
"if you lose the stick, chances are you'll lose the jeep......"

Offline XJHERO

  • Talks waaay too much!
  • Posts: 2041
  • Soberphobic
Re: Who machines flywheels in Calgary?
« Reply #8 on: October 19, 2011, 08:52:31 PM »
i dont think sandpaper will get rid of hot spots, you have to cut that crap off. It might look like its gone but it goes deeper than the surface.
Just saying
Logged
Like ivry soap....pure as frack
DD
Get at me Wolf

Offline 4PLAYZJ

  • UberWheeler
  • Posts: 423
Re: Who machines flywheels in Calgary?
« Reply #9 on: October 23, 2011, 11:42:23 AM »
To have it done properly you don't "Machine" flywheels you have to have them ground.  Call Larry's transmission in the S.E.  They are just up the hill from modern.
Logged
Pages: [1]   Go Up
« previous next »