Calgary Jeep Association

Author Topic: re;jeeptj2003  (Read 1806 times)

0 Members and 3 Guests are viewing this topic.

Offline el duke

  • Stocker
  • Posts: 19
re;jeeptj2003
« on: December 28, 2011, 04:11:50 PM »
 Well i bench tested the starter,it works fine
AAm not getting any power from the ignition,
to the starter,relays are ok and fuses are ok
any suggestions?


Offline apeman

  • Talks waaay too much!
  • Posts: 1012
  • not as grumpy
Re: re;jeeptj2003
« Reply #1 on: December 28, 2011, 04:19:15 PM »
Check your grounds as a start.
Getting grumpier every day.
99 XJ - It's got sum stuff ,Noel free stuff..
98 ZJ - It's just ugly, but bigger than your Rubi

Offline JackstandJohnny

  • Talks waaay too much!
  • Posts: 4727
  • where Jeeps go to die
Re: re;jeeptj2003
« Reply #2 on: December 28, 2011, 09:27:26 PM »
neutral safety switch?
~ rescue green JKUR on 35s.  typical rubicon build

Offline el duke

  • Stocker
  • Posts: 19
Re: re;jeeptj2003
« Reply #3 on: December 29, 2011, 01:01:04 PM »
 I will check the grounds today.
This is a standar trans. so i dont think the neutral switch applies,
but thanks.
What about a clutch relay?
The last time this happened i had to replace sterring column assembly cause actuator switch was broken 1200 bucks

Offline Darkcalling

  • Winch Wench
  • Posts: 42
Re: re;jeeptj2003
« Reply #4 on: December 29, 2011, 01:28:19 PM »
Neutral safety switch clutch relay same beast really but check it first they go out on occasion.
1999 Grand Cherokee Leredo 31s, 2000 TJ Sahara stock with 31s, 2007 Stang GT ragtop cold air and exhaust, 2011 Ram 3500 Cold air and exhaust so far.

Offline binare

  • That CB Yapper
  • Posts: 771
Re: re;jeeptj2003
« Reply #5 on: December 29, 2011, 04:45:42 PM »
I will check the grounds today.
This is a standar trans. so i dont think the neutral switch applies,
but thanks.
What about a clutch relay?
The last time this happened i had to replace sterring column assembly cause actuator switch was broken 1200 bucks

or you could buy the actuator switch at napa for 40 bucks.

Offline Rubi03 jef

  • Talks waaay too much!
  • Posts: 1918
  • she never understands
Re: re;jeeptj2003
« Reply #6 on: December 29, 2011, 06:36:43 PM »
come on   just install a push button start .                       ;D ;D ;D
04 rubicon <4'' X series RC lift, 1.25'' RC body lift, 1'' RC MML, CV rear drive shaft,  Stubby front bumper, CB,35 MTZ" ,Hi Lifter 54'',LED tail lights , flat fenders, LED front Flasher, half doors, Light force spots, and CDN M101 custom Military trailer

Offline el duke

  • Stocker
  • Posts: 19
Re: re;jeeptj2003
« Reply #7 on: December 30, 2011, 01:08:06 PM »
 Ya i have not looked at the ignitionn yet.
Am just working on that push button start rt. now

Offline el duke

  • Stocker
  • Posts: 19
Re: re;jeeptj2003
« Reply #8 on: January 02, 2012, 06:09:17 PM »
 Tried the push button start,it worked once!!!!!!!!!
Thought i had her licked.Did not work a gain.
Something must be broken in the ignition,i even moved the
20amp fuse in glove box to no avail.
Anyone else have this problem?
BEATS ME?

Offline el duke

  • Stocker
  • Posts: 19
Re: re;jeeptj2003
« Reply #9 on: January 06, 2012, 06:55:47 PM »
 Finally got the jeep in the garage.
Pulled apart the ignition,and it was a broken,
ignition actuator pin.Here we go again! Part not sold seperately,
pick a part, i guess ,FRICKIN POT METAL PIECE,what challenged
idiot came up with this schematics for this

Offline binare

  • That CB Yapper
  • Posts: 771
Re: re;jeeptj2003
« Reply #10 on: January 08, 2012, 04:43:13 PM »
Why dont you just buy a new one instead of wasting your time like this?

Offline el duke

  • Stocker
  • Posts: 19
Re: re;jeeptj2003
« Reply #11 on: January 11, 2012, 03:43:34 PM »
 Ya after all that it was the
actuator.AA piece fell off a fter disassembling
steering column,i knew that was the problem.
Thanks for all the input.
I just was not sure  ;D