Calgary Jeep Association

« previous next »
Pages: [1]   Go Down

Author Topic: Need all the knowledge I can get.  (Read 1914 times)

0 Members and 1 Guest are viewing this topic.

Offline Bnf5586

  • Stocker
  • Posts: 1
Need all the knowledge I can get.
« on: September 12, 2014, 07:34:25 PM »
I have a 1998 Cherokee sport. Inline6 4.0l 5 speed, damaged the o2 sensor wiring, have since replaced the wiring but now the truck will stall randomly and run rough. But at high rpm it runs mint, no temp issues.
The tps, throttle body, and 02's have all be replaced. Any help would be hugely helpful. Cheers.
Logged

Offline hps4evr

  • Administrator
  • Talks waaay too much!
  • Posts: 2959
Re: Need all the knowledge I can get.
« Reply #1 on: September 12, 2014, 07:48:25 PM »
Are you 100% certain the wiring was repaired properly and each wire connects to proper spot on connector?
Logged
YJ=Y’all Jealous

Offline Vinman

  • CJA Executive
  • Talks waaay too much!
  • Posts: 2237
Re: Need all the knowledge I can get.
« Reply #2 on: September 12, 2014, 08:00:01 PM »
When repairing the 02 sensor wiring were the wires soldered together?
Logged
/l ,[____],
 l---L -OlllllllO-
 ()_)-()_)-o-)_)

Quote from: Bnine link=topic=25904.msg162940#msg162940      date=1341881306
. 
 Resident prick is my job and it took me ten years to earn that title

Offline SwampSinger

  • CJA Members
  • Talks waaay too much!
  • Posts: 6172
  • Baconator
    • mmmmm-bacon
Re: Need all the knowledge I can get.
« Reply #3 on: September 12, 2014, 08:14:17 PM »
even soldered... it created different resistances and fucks the readings...

I had to change my whole harness...
Logged

Offline Vinman

  • CJA Executive
  • Talks waaay too much!
  • Posts: 2237
Re: Need all the knowledge I can get.
« Reply #4 on: September 12, 2014, 09:24:09 PM »
Quote from: SwampSinger on September 12, 2014, 08:14:17 PM
even soldered... it created different resistances and fucks the readings...

I had to change my whole harness...

From what I've read on the GM LS motors and I assume on others as well,  the 02's gather an air sample from within the wires and use that as a baseline (kinda sort of) and soldering actually screws up the sample, the proper way to splice the wires is to use a crimp and seal everything in heat shrink. At least thats the way I understood it.
Logged
/l ,[____],
 l---L -OlllllllO-
 ()_)-()_)-o-)_)

Quote from: Bnine link=topic=25904.msg162940#msg162940      date=1341881306
. 
 Resident prick is my job and it took me ten years to earn that title

Offline cLAY

  • Talks waaay too much!
  • Posts: 2377
Re: Need all the knowledge I can get.
« Reply #5 on: September 13, 2014, 09:20:57 AM »
Any codes?
Sometimes the ECM needs to be reset so that it can relearn its baseline parameters.
Any exhaust leaks before the O2?
Logged
..

'93 ZJ, 5.2L, lifted/locked/36s..<gone>
'98 5.9er 4.10s,locked,LA,WJ knuckles

Offline Bnine

  • Talks waaay too much!
  • Posts: 2572
  • Sticky Fingers
Re: Need all the knowledge I can get.
« Reply #6 on: September 15, 2014, 08:41:07 AM »
How does it start? Any smell of fuel?
Logged
My Mechanic Calgary
Mobile Auto Care
403-483-1083
[email protected]
Pages: [1]   Go Up
« previous next »