Calgary Jeep Association

« previous next »
Pages: [1]   Go Down

Author Topic: harmonic balancner issues  (Read 1265 times)

0 Members and 3 Guests are viewing this topic.

Offline JackstandJohnny

  • Talks waaay too much!
  • Posts: 4727
  • where Jeeps go to die
harmonic balancner issues
« on: November 17, 2010, 10:21:13 AM »
the crank pulley/harmonic balancer on the jeep doesn't look to happy on my newly acquired ZJ.  its wobbling something fierce.  i noticed it today after the jeep wouldn't start........ i finally got it going but it was making one hell of a racket.  looked at the drive pulleys and the crank pulley is wobbling something fierce. (so is another freespooling pully)  i have a feeling this is my vibration problem as well.
is it fixable or should i just start pulling this engine out?

cheers
Logged
~ rescue green JKUR on 35s.  typical rubicon build

Offline CatSplat

  • Budget Lift
  • Posts: 183
Re: harmonic balancner issues
« Reply #1 on: November 17, 2010, 12:15:28 PM »
Is the actual pulley wobbling, or just the balancer part?
Logged
Jeep of Theseus

Offline Rubi03 jef

  • Talks waaay too much!
  • Posts: 1918
  • she never understands
Re: harmonic balancner issues
« Reply #2 on: November 17, 2010, 12:27:56 PM »
are all the bolt in and are they all tight

might want to check that
Logged
04 rubicon <4'' X series RC lift, 1.25'' RC body lift, 1'' RC MML, CV rear drive shaft,  Stubby front bumper, CB,35 MTZ" ,Hi Lifter 54'',LED tail lights , flat fenders, LED front Flasher, half doors, Light force spots, and CDN M101 custom Military trailer

Offline WagoneerXJ

  • Talks waaay too much!
  • Posts: 1363
  • Bagon Wagon!
Re: harmonic balancner issues
« Reply #3 on: November 17, 2010, 07:29:48 PM »
just check and replace the balancer if necessary.
Logged
98 XJ Sport 2 Dr, 3", 33's and Bushwacker Flat Flares
87 XJ Wagoneer 5", Dana 44, 34" Swamper TSL's
97 TJ 5.2 Magnum V8 swap, 4" and 33" MTZ's- GF's Jeep
84 Mustang GT-Built 351W 5spd
97 XJ - 3.5", 31" BFG. 370,000 KMS and counting!

Offline cLAY

  • Talks waaay too much!
  • Posts: 2377
Re: harmonic balancner issues
« Reply #4 on: November 17, 2010, 08:13:53 PM »
IS it a 4.0L? They used a 2 piece dampener, an inner ring and outer ring with a rubber band between the two. Sometimes the outer ring will start to walk off or it will spit out the rubber band. Replacement at that point is usually necessary but a used one can be used if it visually looks good.
Logged
..

'93 ZJ, 5.2L, lifted/locked/36s..<gone>
'98 5.9er 4.10s,locked,LA,WJ knuckles

Offline JackstandJohnny

  • Talks waaay too much!
  • Posts: 4727
  • where Jeeps go to die
Re: harmonic balancner issues
« Reply #5 on: November 17, 2010, 11:17:19 PM »
thanks guys,
and ya clay, that sounds like whats happening pretty much.  PITA to change?  just a regular 3 pronged puller should be good to pull it right?   looks like i have to pull the rad too...........
gonna do it this weekend ;)
Logged
~ rescue green JKUR on 35s.  typical rubicon build

Offline The Machinist

  • CJA Members
  • That CB Yapper
  • Posts: 741
  • I’m with stupid!
Re: harmonic balancner issues
« Reply #6 on: November 17, 2010, 11:37:06 PM »
Easy to change, use a harmonic balancer puller.  Three bolts that screw in to it, a 3 jaw will probably just break parts off.  PA sells them cheap, or I have a spare one you can borrow if you feel like driving to coventry hills.
Logged
I just can’t resist a good mud hole!  🤦

Offline Gearhead

  • Talks waaay too much!
  • Posts: 1161
Re: harmonic balancner issues
« Reply #7 on: November 18, 2010, 07:54:52 AM »
Do not pound the replacement on with a hammer  !
Logged

Offline Pookapotamus

  • Talks waaay too much!
  • Posts: 1123
Re: harmonic balancner issues
« Reply #8 on: November 18, 2010, 08:01:34 AM »
is it not about time you sold this johnny? or have you not put enough mony into it to justify selling it?? 

 :P
Logged

Offline JackstandJohnny

  • Talks waaay too much!
  • Posts: 4727
  • where Jeeps go to die
Re: harmonic balancner issues
« Reply #9 on: November 18, 2010, 09:26:04 AM »
thanks jamey. PA will do ;)

pook this one ain't really worth selling :)  when it dies, i'll either fix it or strip it for parts ;)
Logged
~ rescue green JKUR on 35s.  typical rubicon build

Offline Pookapotamus

  • Talks waaay too much!
  • Posts: 1123
Re: harmonic balancner issues
« Reply #10 on: November 18, 2010, 09:36:43 AM »
dont lie, its on kijiji allready isint it!
Logged

Offline JackstandJohnny

  • Talks waaay too much!
  • Posts: 4727
  • where Jeeps go to die
Re: harmonic balancner issues
« Reply #11 on: November 18, 2010, 09:39:11 AM »
thats it pook. you're comin over to help me fix it ;)
Logged
~ rescue green JKUR on 35s.  typical rubicon build

Offline Knox

  • That CB Yapper
  • Posts: 649
Re: harmonic balancner issues
« Reply #12 on: November 18, 2010, 09:51:51 AM »
Quote from: JohnnyC on November 18, 2010, 09:39:11 AM
thats it pook. you're comin over to help me fix it ;)

If you want another beer drinking supervisor give me a shout I'm around this weekend. that way you know Pook doesn't have to watch you all the time, he can take a nap or 2
Logged
2003 TJ
"Your TJ has the aerodynamics of a brick"
"if you lose the stick, chances are you'll lose the jeep......"

Offline Pookapotamus

  • Talks waaay too much!
  • Posts: 1123
Re: harmonic balancner issues
« Reply #13 on: November 18, 2010, 11:31:15 AM »
bring it to my place we can test my plama on it and fix it real good!  8)
Logged

Offline mike s

  • UberWheeler
  • Posts: 361
  • Good times!
Re: harmonic balancner issues
« Reply #14 on: November 18, 2010, 06:55:49 PM »
Let me know if you guys need a hand. Some run-out on balancer is okay, not a 8 600RPM race engine....right? If you can't fit the puller in with the rad in place, you can sometimes walk the balancer off with a couple of pry bars
Logged
'94 YJ, 2.5" RE, 1"BL on 35"s, 8.8 w 4.88
oldEnuff2NObetter

but still can't help myself
Pages: [1]   Go Up
« previous next »